diff --git a/src/lqos.conf.new.discuss b/src/lqos.conf.new.discuss
new file mode 100644
index 00000000..66583689
--- /dev/null
+++ b/src/lqos.conf.new.discuss
@@ -0,0 +1,174 @@
+lqos_directory = '/opt/libreqos/src'
+queue_check_period_ms = 1000
+
+[tuning]
+stop_irq_balance = true
+netdev_budget_usecs = 8000
+netdev_budget_packets = 300
+rx_usecs = 8
+tx_usecs = 8
+disable_rxvlan = true
+disable_txvlan = true
+disable_offload = [ "gso", "tso", "lro", "sg", "gro" ]
+
+interface_mapping = [
+       { name = "enp1s0f1", redirect_to = "enp1s0f2", scan_vlans = false },
+       { name = "enp1s0f2", redirect_to = "enp1s0f1", scan_vlans = false }
+]
+vlan_mapping = []
+
+# NMS/CRM Integration
+
+[NMS]
+
+# If a device shows a WAN IP within these subnets...
+# assume they are behind NAT / un-shapable, and ignore them
+
+ignoreSubnets = ['192.168.0.0/16']
+allowedSubnets = ['100.64.0.0/10']
+
+[IspConfig]
+
+# 'fq_codel' or 'cake diffserv4'
+# 'cake diffserv4' is recommended
+# sqm = 'fq_codel'
+
+sqm = 'cake diffserv4'
+
+# Used to passively monitor the network for before / after comparisons. Leave as False to
+# ensure actual shaping. After changing this value, run "sudo systemctl restart LibreQoS.service"
+
+monitorOnlyMode = False
+
+# How many Mbps are available to the edge of this network
+
+upstreamBandwidthCapacityDownloadMbps = 1000
+upstreamBandwidthCapacityUploadMbps = 1000
+
+# Devices in ShapedDevices.csv without a defined ParentNode will be placed under a generated
+# parent node, evenly spread out across CPU cores. Here, define the bandwidth limit for each
+# of those generated parent nodes.
+
+generatedPNDownloadMbps = 1000
+generatedPNUploadMbps = 1000
+
+# Interface connected to core router
+interfaceA = 'eth1'
+
+# Interface connected to edge router
+interfaceB = 'eth2'
+
+# WORK IN PROGRESS. Note that interfaceA determines the "stick" interface
+# I could only get scanning to work if I issued ethtool -K enp1s0f1 rxvlan off
+
+OnAStick = False
+# VLAN facing the core router
+
+StickVlanA = 0
+# VLAN facing the edge router
+
+StickVlanB = 0
+
+# Allow shell commands. False causes commands print to console only without being executed.
+# MUST BE ENABLED FOR PROGRAM TO FUNCTION
+
+enableActualShellCommands = True
+
+# Add 'sudo' before execution of any shell commands. May be required depending on distribution and environment.
+runShellCommandsAsSudo = False
+
+# Allows overriding queues / CPU cores used. When set to 0, the max possible queues / CPU cores are utilized. Please
+# leave as 0.
+
+queuesAvailableOverride = 0
+
+# Some networks are flat - where there are no Parent Nodes defined in ShapedDevices.csv
+# For such flat networks, just define network.json as {} and enable this setting
+# By default, it balances the subscribers across CPU cores, factoring in their max bandwidth rates
+# Past 25,000 subsribers this algorithm becomes inefficient and is not advised
+
+useBinPackingToBalanceCPU = True
+
+[InfluxDB]
+
+# Bandwidth & Latency Graphing
+influxDBEnabled = True
+influxDBurl = "http://localhost:8086"
+influxDBBucket = "libreqos"
+influxDBOrg = "Your ISP Name Here"
+influxDBtoken = ""
+
+[Splynx]
+
+# Splynx Integration
+automaticImportSplynx = False
+splynx_api_key = ''
+splynx_api_secret = ''
+# Everything before /api/2.0/ on your Splynx instance
+splynx_api_url = 'https://YOUR_URL.splynx.app'
+
+# UISP integration
+[UISP]
+automaticImportUISP = False
+uispAuthToken = ''
+# Everything before /nms/ on your UISP instance
+UISPbaseURL = 'https://examplesite.com'
+# UISP Site - enter the name of the root site in your network tree
+# to act as the starting point for the tree mapping
+uispSite = ''
+
+# Strategy:
+# * "flat" - create all client sites directly off the top of the tree,
+#   provides maximum performance - at the expense of not offering AP,
+#   or site options.
+# * "full" - build a complete network map
+uispStrategy = "full"
+
+# List any sites that should not be included, with each site name surrounded by ''
+# and separated by commas
+
+excludeSites = []
+
+# If you use IPv6, this can be used to find associated IPv6 prefixes
+# for your clients' IPv4 addresses, and match them
+# to those devices
+
+findIPv6usingMikrotik = False
+
+# If you want to provide a safe cushion for speed test results to prevent customer complaints,
+# you can set this to 1.15 (15% above plan rate). If not, you can leave as 1.0
+
+bandwidthOverheadFactor = 1.0
+
+# For edge cases, set the respective ParentNode for these CPEs
+exceptionCPEs = {}
+
+# exceptionCPEs = {
+#  'CPE-SomeLocation1': 'AP-SomeLocation1',
+#  'CPE-SomeLocation2': 'AP-SomeLocation2',
+# }
+
+# API Auth
+apiUsername = "testUser"
+apiPassword = "changeme8343486806"
+apiHostIP = "127.0.0.1"
+apiHostPost = 5000
+
+httpRestIntegrationConfig = {
+    'enabled': False,
+    'baseURL': 'https://domain',
+    'networkURI': '/some/path',
+    'shaperURI': '/some/path/etc',
+    'requestsConfig': {
+        'verify': True,  # Good for Dev if your dev env doesnt have cert
+         'params': {  # params for query string ie uri?some-arg=some-value
+           'search': 'hold-my-beer'
+         },
+        #'headers': {
+           # 'Origin': 'SomeHeaderValue',
+        #},
+    },
+    # If you want to store a timestamped copy/backup of both network.json and Shaper.csv each time they are updated,
+    # provide a path
+    # 'logChanges': '/var/log/libreqos'
+}