We currently probe dirty block tracking bitmaps by looking at the loaded
ones ('dirty-bitmaps'). Unfortunately those may not yet be populated on
incoming migration when the image was not yet activated, but we need to
know which ones are stored in the image so that we don't migrate those
explicitly, which would fail.
Load the list of bitmaps in a qcow2 image from the format specific data,
which is already loaded at that point.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Rather than looking for 30 specific nodenames (via a loop) iterate
everything in the hash table (in a sorted order). This simplifies the
code and provides more test outputs on previously-ignored nodenames.
The listing of internal snapshots in the output was also missing a
newline, which would now cause problems with multiple images reproted.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The 'data_file_raw' flag of qcow2 notifies that all data inside the
'data_file' is a raw image so can be used standalone without the
metadata without any problem (except for not updating the dirty
bitmaps).
Our migration safety checks will allow skipping the migration safety
check for these files as during migration we know it's safe to re-create
this on the destination in a location that isn't shared.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Refactor the parts of qemuBlockGetNamedNodeData which fetch the names of
internal snapshots present in the on-disk state of QCOW2 images to also
extract the presence of the 'vmstate' section.
This requires conversion of the snapshot list to a hash table as we
always know the name of the snapshot that we're looking for, and the
hash table allows also storing of additional data which we'll use to
store the presence of the 'vmstate'.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Store the names of internal snapshots present in supported images in the
data we dump from 'query-named-block-nodes' so that the upcoming changes
to the internal snapshot code can access it.
To test this we use the bitmap detection test cases which can be easily
extended to dump this data.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Such images don't support stuff like dirty bitmaps. Note that the
synthetic test for detecting bitmaps is used as an example to prevent
adding additional test cases.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
Based on the 'snapshots' example with manual tweaks to introduce
inactive, transient, inconsistent and duplicate bitmaps in various parts
of the chain to exercise detection and new validation code.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Use test data which conforms to the new semantics which changed in the
previous patch.
The test data was created by the same set of commands as originally in
commit 0b27b655b1
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Use test data which conforms to the new semantics which changed in the
previous patch.
The test data was created by the same set of commands as originally in
commit 9aac9d5bda
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
They will be replaced by a different set which will test scenarios
relevant for the new semantics.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Some branches were not covered and thus we didn't catch that the bitmaps
are not re-enabled if nothing is merged into them. Two bitmaps are
necessary to reliably test the case due to hash table ordering.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Tested-by: Daniel P. Berrangé <berrange@redhat.com>
Add a case where a bitmap spanning multiple images is missing one of the
intermediate components.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Add a faked qemu output which would simulate scenario where libvirt
would take a snapshot and checkpoint simultaneously. This is visible in
libvirt-2-format node where bitmap 'c' appears, but bitmap 'b' which is
active in the previous layer is not present.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Add test data gathered from a run of qemu after creating bitmaps and
snapshots together in various combinations.
The following sequence of commands was used to achieve the
configuration:
virsh checkpoint-create-as VM --name a
virsh snapshot-create-as VM --disk-only
virsh snapshot-create-as VM --disk-only
virsh checkpoint-create-as VM --name b
virsh checkpoint-create-as VM --name c
virsh snapshot-create-as VM --disk-only
virsh checkpoint-create-as VM --name d
virsh snapshot-create-as VM --disk-only
virsh checkpoint-create-as VM --name current
Note that VM was restarted after these operations to allow renumbering
of the bitmaps in a more human-readable way.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The real data gathered for the 'basic' test case don't exercise some
fields. Add a copy with a few values modified manually.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Test the extraction of data about changed block tracking bitmaps. The
first test case adds a simple scenario of multiple bitmaps in one layer.
The test data will be also later reused for testing the code that
determines which bitmaps to merge for an incremental backup.
The sequence of bitmaps was created by the libvirt checkpoint API with
the following sequence of commands:
virsh checkpoint-create-as VM --name a
virsh checkpoint-create-as VM --name b
virsh checkpoint-create-as VM --name c
virsh checkpoint-create-as VM --name d
virsh checkpoint-create-as VM --name current
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Peter Krempa